Author Topic: E36 M42 tranny and E30 M42 tranny... (Read 10824 times)

romkasponka · « **Reply #15 on:** January 14, 2009, 08:11:35 AM »

Quote from: Daniele30;64646

Do you have any issue with the prop shaft(long shaft) ?? direct fit by using
e36 front & rear long shaft ?

You can adjust propshaft lenght..

fabe · « **Reply #16 on:** January 14, 2009, 08:59:37 AM »

Quote from: romkasponka;64653

You can adjust propshaft lenght..

just to double confirm.. You mean adjust the existing E30 propshaft?? Cos daniel's question was on the E36 propshaft..

romkasponka · « **Reply #17 on:** January 14, 2009, 05:30:08 PM »

Quote from: fabe;64655

just to double confirm.. You mean adjust the existing E30 propshaft?? Cos daniel's question was on the E36 propshaft..

E36 propshaft is adjustable also...

fabe · « **Reply #18 on:** January 15, 2009, 01:11:41 AM »

I understand that they are adjustable...

So you used back the E30 propshaft with the E36 gearbox??

romkasponka · « **Reply #19 on:** January 15, 2009, 02:19:58 AM »

Quote from: fabe;64709

I understand that they are adjustable...

So you used back the E30 propshaft with the E36 gearbox??

I used all, NOT ONLY BACK, E30 driveshaft with E36 gearbox in E30

fabe · « **Reply #20 on:** January 15, 2009, 03:00:07 AM »

Quote from: romkasponka;64712

I used all, NOT ONLY BACK, E30 driveshaft with E36 gearbox in E30

Thanks... That was the confirmation I was looking for...

romkasponka · « **Reply #21 on:** January 15, 2009, 03:24:13 AM »

Quote from: fabe;64713

Thanks... That was the confirmation I was looking for...

you are welcome...

Daniele30 · « **Reply #22 on:** January 15, 2009, 07:27:56 AM »

Quote from: romkasponka;64717

you are welcome...

oh thank god...

I think i shouldn't have any problem installing e36 box onto my e30.

I need to buy the aluminium shifter balancer too

I'm gonna use 87' 240 manual long shaft. hopefuly it can be fit as well.

fabe · « **Reply #23 on:** January 15, 2009, 08:45:14 AM »

romkasponka, actually I was trying to look for the thread on the transmission change.. Can't seem to locate it..

Want to know also about the lingkage rod. Are u using the one from the E30? Any modification required?

Daniele30 · « **Reply #24 on:** January 15, 2009, 09:45:08 AM »

can i use this from e36 coupe ??

or have to use the e30 one ?

the aluminium shifter balancer

wazzu70 · « **Reply #25 on:** February 26, 2013, 12:58:44 PM »

Quote from: romkasponka;64653

You can adjust propshaft lenght..

Propshaft is the shaft from CSB to trans. I dont think this can be changed. I assume you are talking about the rear section that is splined?

I tried fitting the E30 driveline in the car with a G250 installed and the propshaft was too long. The CSB was too far behind the chassis mounting points.

Do people weld in new chassis attachment points for the CSB?

romkasponka · « **Reply #26 on:** February 26, 2013, 01:46:50 PM »

In my case driveshaft was shortened through splines and was short enough to install E36 ZF 225 gearbox. In future I am planning to replace it with one peace driveshaft in order to move engine backwards and save some weight.

If you miss few millimeters you can elongate the holes.