Author Topic: COP Brackets: Your Preferences? (Read 81122 times)

hoevesruperd · « **Reply #195 on:** May 08, 2008, 11:06:14 AM »

this is my setup
haledj plate and mounting hardware
FCP groton (ebay) coils

it was a very very simple job. 20min max

cristimm · « **Reply #196 on:** February 18, 2010, 12:31:01 PM »

Hello,

Can anyone send me the plate drawing in dwg format?

1991 E30 M42 · « **Reply #197 on:** February 18, 2010, 02:36:11 PM »

there is a drawing around somewhere it wouldn't take but about a minute do draw up

4banger · « **Reply #198 on:** February 18, 2010, 03:37:02 PM »

i need to do 4 of these up.

1991 E30 M42 · « **Reply #199 on:** February 18, 2010, 07:42:45 PM »

Here is a drawing that I put together real fast
cop.dwg

If you need I can upload the original .ipt inventor drawing as well

cristimm · « **Reply #200 on:** February 19, 2010, 03:00:37 PM »

Thank you all.

What is the thickness of the plate?

1991 E30 M42 · « **Reply #201 on:** February 19, 2010, 04:34:01 PM »

i think the plate is 1/4"

cristimm · « **Reply #202 on:** February 20, 2010, 11:57:01 AM »

Wow that's preety thick (6.35mm)

visionracingdevelopments · « **Reply #203 on:** February 21, 2010, 05:22:23 PM »

I used 5mm

4banger · « **Reply #204 on:** February 21, 2010, 06:40:35 PM »

what coils do you use?

cristimm · « **Reply #205 on:** April 28, 2010, 03:08:48 PM »

Today I received my bremi coils. Still looking for somebody to make me the plate.

iron-H · « **Reply #206 on:** May 06, 2010, 07:35:12 AM »

Sorry for picking this thread up again.
So what wireharness do you all use with which coils?
Do most coils of e38 ;v8 r6; or else fit with the wireharness from a e36 323i?
Are the plugs all the same especially from the m62, m64, m50, m52, m54, s54,... to the coils?

i�m driving a e36 Compact with the m42 and beeing often at the N�rburgring ;-) So it must been working for this sesion... :-)

Kind regards

cristimm · « **Reply #207 on:** June 21, 2010, 12:12:26 PM »

Here is my finished E36 M42 COP conversion:

Thank you all for your help.

A few remarks regarding the plate:
- for E36 car that little tail from the back needs to be cut in half (i did not used anyway so I could have just cut it all) because it is very close to the firewall
- I used M5 bolts for the coils (like the original coils were fixed) this allows a little clearence which can compensate for small imperfections in the cutting of the plate.

xsjado · « **Reply #208 on:** June 22, 2010, 11:12:40 AM »

how do you connect the COP to the existing wiring harness?pics please.

rob_e30 · « **Reply #209 on:** June 22, 2010, 05:51:57 PM »

It's plug and play for E30 M42's and early E36 M42's. If you have 4 coil connectors in your harness then you are good to go. If you have an E36 with the single round connector then you need to make up a new harness or splice into your existing.

Check out http://www.hqautosport.com for more information.