Author Topic: Will these fit? What offset should i look for? (Read 5465 times)

goober · « **on:** January 03, 2011, 05:54:29 PM »

16x7 4x100 +35 offset and BSM of 5.303
Because I dont know how to insert pictures, they are MSR style 068.
Any help is greatly appreciated
Thank you

DesktopDave · « **Reply #1 on:** January 03, 2011, 08:17:42 PM »

http://www.1010tires.com/wheeloffsetcalculator.asp
Here's a good thread too:
http://www.maxbimmer.com/forums/showthread.php?t=54146

Stock rim (that's what I run) is a 14x6 with an offset of 35mm. Your wheel will be 10mm closer to the strut (about 3/8"), 16mm farther out. If I was in your shoes I'd be out there with a ruler to see how much room I had.

They seem a little close for (my) comfort, but a little rubbing isn't the end of the world. Spacers are pretty cheap (don't forget longer lug bolts too), so even if you make a mistake you're not totally out of luck.

goober · « **Reply #2 on:** January 03, 2011, 09:30:10 PM »

Nice threads, I have checked out the second one however the first one is new to me. I'd prefer to have no rubbing whatsoever, however if I were to put say 215/40/16 on them, could I use them on my 318is without causing permanent damage? If there would be rubbing, should I get 10mm spacers? Thank you for your help, its really appreciated as I'm new to this.

asubimmer · « **Reply #3 on:** January 03, 2011, 10:24:42 PM »

depending on the tire size, YES. I would deff suggest at least a 15mm spacer. Like Dave said the rim itself will be 10mm closer to the strut and just over 1mm out past the old rim.

goober · « **Reply #4 on:** January 04, 2011, 08:03:03 AM »

Sorry but what brand or make would recommend?
Thank you

asubimmer · « **Reply #5 on:** January 04, 2011, 11:26:24 AM »

I would stick with the big names. Tires are VERY important.

-Falken is prob the best bang for buck.

Good names, in no specific order
-Bridgestone
-Continental
-Goodyear
-Hankook
-Michelin
-Yokohoma

You can go outside these brands but I would not recommend it.

goober · « **Reply #6 on:** January 04, 2011, 03:13:26 PM »

Ok thanks, I'll probably end up getting yokohamas. How about for the spacers, I've been looking at eibach, and do they need to have certain specifications I need to know about?
thank you

asubimmer · « **Reply #7 on:** January 04, 2011, 06:43:28 PM »

Just make sure they are 4x100 and are hubcentric to e30's (57.1mm)

goober · « **Reply #8 on:** January 04, 2011, 08:46:59 PM »

Thank you very much for your help. Now for a pure aesthetic question...silver gloss? Or black?
Thanks

Btw, I have an alpine white 91

asubimmer · « **Reply #9 on:** January 05, 2011, 10:27:28 PM »

Personally I would either do a bronze or a gunmetal wheel. Can depend on the wheel though

goober · « **Reply #10 on:** January 06, 2011, 07:36:04 PM »

Well thanks for all of your help. I understand a lot more about e30 fitments and how to fit my car thanks to you guys. I'm actually considering a different wheel now, same measurements however, a little more of an offset, however I will put 15mm spacers. They look similar to the BBS LMs. Black mesh, and polished lip. I'll be sure to post pictures when I get them on.
Thank you