« previous next »
Pages: [1]   Go Down

Author Topic: clutch pedal pulsating  (Read 3407 times)

n2motorsports

  • Full Member
  • ***
  • Thank You
  • -Receive: 0
  • Posts: 170
    • View Profile
clutch pedal pulsating
« on: November 02, 2007, 09:56:11 AM »
is it normal to feel the clutch pulsating while shifting gears?  could this be a sign of a bad clutch slave cylinder or bad motor mounts?  

car shifts into gears smoothly, without any slippage.
Logged

EN318isPDX

  • Hero Member
  • *****
  • Thank You
  • -Receive: 0
  • Posts: 650
    • View Profile
    • http://www.cardomain.com/id/ItotheAtotheN
clutch pedal pulsating
« Reply #1 on: November 02, 2007, 10:00:21 AM »
Quote from: n2motorsports;37048
is it normal to feel the clutch pulsating while shifting gears?  could this be a sign of a bad clutch slave cylinder or bad motor mounts?  

car shifts into gears smoothly, without any slippage.


I'd guess maybe one of your tranny mounts? not really sure though im thinkin it might be one of them not being bolted on
Logged
WTB 97+ M3 Front Strut Assembly and 97+ M3 Control Arms (caster is important)
WTB Driver side Diamondschwartz fender PST

haledj

  • Sr. Member
  • ****
  • Thank You
  • -Receive: 0
  • Posts: 408
    • View Profile
    • http://www.rose-hulman.edu/~haledj/
clutch pedal pulsating
« Reply #2 on: November 02, 2007, 10:46:15 AM »
it could be your throwout bearing, if it is it will start squeeking/grinding soon
Logged

sheepdog

  • Site Admin
  • Administrator
  • Legendary
  • *****
  • Thank You
  • -Receive: 4
  • Posts: 1272
    • View Profile
clutch pedal pulsating
« Reply #3 on: November 02, 2007, 11:39:21 AM »
Could also be that the pressure plate fingers may be failing. Had this happen on a pickup.

I would check the engine and trans mounts and if they are good, start planning on a clutch job. Even if it is only the T/O bearing, do the entire clutch while you are there.
Logged
"When trouble arises and things look bad, there is always one individual who perceives a solution and is willing to take command. Very often, that individual is crazy." --Dave Berry

EN318isPDX

  • Hero Member
  • *****
  • Thank You
  • -Receive: 0
  • Posts: 650
    • View Profile
    • http://www.cardomain.com/id/ItotheAtotheN
clutch pedal pulsating
« Reply #4 on: November 02, 2007, 12:11:00 PM »
Quote from: sheepdog;37055
Could also be that the pressure plate fingers may be failing. Had this happen on a pickup.

I would check the engine and trans mounts and if they are good, start planning on a clutch job. Even if it is only the T/O bearing, do the entire clutch while you are there.


When i got my car the guy told me the clutch was bad. Turned out it was the hole tranny. I had about 25% left on the clutch disc so i replaced EVERYTHING anyway. New clutch really made me happy, i am glad i didnt put it off
Logged
WTB 97+ M3 Front Strut Assembly and 97+ M3 Control Arms (caster is important)
WTB Driver side Diamondschwartz fender PST

n2motorsports

  • Full Member
  • ***
  • Thank You
  • -Receive: 0
  • Posts: 170
    • View Profile
clutch pedal pulsating
« Reply #5 on: November 02, 2007, 02:07:49 PM »
has anyone replaced their clutch themselves?  I haven't really been under the e30 much, so im not sure how difficult it is to reach some of the bellhousing bolts....it's an absolute pain on my nissan.
Logged

EN318isPDX

  • Hero Member
  • *****
  • Thank You
  • -Receive: 0
  • Posts: 650
    • View Profile
    • http://www.cardomain.com/id/ItotheAtotheN
clutch pedal pulsating
« Reply #6 on: November 02, 2007, 02:30:35 PM »
I have done it recently on my M42 and the hardest bolts to get out was the ones from behind the bell housing that holds the starter in. They have a nut on one side so i had to tag team it to get it out
Logged
WTB 97+ M3 Front Strut Assembly and 97+ M3 Control Arms (caster is important)
WTB Driver side Diamondschwartz fender PST

gearheadE30

  • Legendary
  • ******
  • Thank You
  • -Receive: 0
  • Posts: 1245
    • View Profile
clutch pedal pulsating
« Reply #7 on: November 03, 2007, 05:32:29 PM »
As for checking the engine mounts, how far should the upper pan be fromt he steering rack? I can move the engine my pushing on the upper intake, and it makes a bit of a thunking noise.
Logged

1991 318is Turbo
1989 Caprice Classic Wagon named Humphrey
1979 Suzuki GS750E

DCColegrove

  • Newbie
  • *
  • Thank You
  • -Receive: 0
  • Posts: 37
    • View Profile
    • http://www.bandcforeigncar.com
clutch pedal pulsating
« Reply #8 on: November 04, 2007, 02:47:09 AM »
If the pedal is pulsating it is probably either the T/O Brng or the Pressure plate...
 It would be nuts to pull the trans and only replace one or the other though so...
 We say you need a clutch
Logged

eric ^__^

  • Guest
clutch pedal pulsating
« Reply #9 on: November 09, 2007, 02:55:37 PM »
Quote from: haledj;37053
it could be your throwout bearing, if it is it will start squeeking/grinding soon


yep, mine is squeaking now. I wonder how long I have! Replacing the clutch/bearings on wednesday. It's amazing how long you can go with a bad clutch.

I've read a few posts about installing a lightened M20 flywheel. Oddly enough there just happens to be a lightened/balanced M20 wheel at the shop as we speak.

I wish I had time to get the clutch balanced, but oh well.
Logged
Pages: [1]   Go Up
« previous next »