Author Topic: COP Conversion Brackets (Read 65303 times)

BrandC · « **Reply #15 on:** September 24, 2007, 12:32:47 PM »

Let us know how you will be handling payment.

haledj · « **Reply #16 on:** September 24, 2007, 01:48:10 PM »

Payment will be done through paypal, If this is a problem then we can work something else out, but the part will not ship until I have money in hand.

haledj · « **Reply #17 on:** September 27, 2007, 03:14:13 PM »

I now have all the plates done.

I will get a shipping estimate tomorrow morning to the lower 48 states.

PM me if you want one with an address and I will send you my paypal info and a price.

haledj · « **Reply #18 on:** October 01, 2007, 07:56:23 AM »

Shipping is around $5 for ground

I have ordered all the hardware that will be required for installation and it should be in soon. If you want this stuff too, it will be an additional $7, but also a couple more days of waiting.

it will include:
8 M6X1 cap screws
2 60 mm M6X1 studs
4 M6X1 bolts
4 6mm washers

BTW I stopped by my local hardware store and just the cap screws would cost about $7 if you bought them individually, and they didn’t even have studs.

so for the totals, $75 for a plate shipped, and $82 for a plate plus all the hardware. Or if you would like, $12 for just the hardware.

I can ship out plates as soon as I get the money, so give me a PM!

BrandC · « **Reply #19 on:** October 02, 2007, 01:11:48 PM »

Sent you PM!

haledj · « **Reply #20 on:** October 03, 2007, 12:16:34 PM »

here are some pictures of the completed plates, if you would like pictures of something more specific, let me know

this is the hardware included in the installation pack

pictures of the plates

*note the plate that has the coils mounted on it has been polished and the ones that are being sold are not polished like the one that does not have coils mounted on it.
besides the finish they are identical

BrandC · « **Reply #21 on:** October 03, 2007, 02:26:06 PM »

fuckin' sweet.

kowalski · « **Reply #22 on:** October 03, 2007, 06:43:57 PM »

nice job on the VC

cenotaph · « **Reply #23 on:** October 04, 2007, 08:44:47 AM »

are you still able to fit the spark plug wire cover after this?

haledj · « **Reply #24 on:** October 04, 2007, 11:06:26 AM »

Quote from: cenotaph;34947

are you still able to fit the spark plug wire cover after this?

I havent tried but I can look later today

1988E30M3 · « **Reply #25 on:** October 04, 2007, 12:31:54 PM »

I assume not, but will this mod post any problems for cars running a modified chip?
I will be installing a 93 octane Mark D chip in my 318is soon and would not want to discover any incompatibility between the chip and this mod.
Also, performance gains, if any?

TIA

haledj · « **Reply #26 on:** October 04, 2007, 06:39:28 PM »

this will work with any chip as the ECU sees no difference. I have no proof of increased power but people claim to notice better trottle respose and better idle. In short you will have a better spark and will never have to buy spark plug wires ever again.

SheldonJace · « **Reply #27 on:** October 04, 2007, 07:15:43 PM »

I just closed my small town bank account and am waiting to get back home to open up a new one with a nation wide bank so when that does happen I will most definitely be buying a bracket if there are any left.

haledj · « **Reply #28 on:** October 09, 2007, 12:17:20 AM »

Quote from: cenotaph;34947

are you still able to fit the spark plug wire cover after this?

There is no way to do it and have it still look good. You could use longer studs and put holes in the cover and mount it that way but I think that would look bad.

vitesse · « **Reply #29 on:** October 11, 2007, 11:53:13 AM »

Do you still have any of these in stock with the mounting hardware?? thanks