Author Topic: Denis (dude8383) is an UNGRATEFUL TRAITOR (Read 27809 times)

e30guydownunder · « **Reply #90 on:** September 05, 2008, 04:31:04 AM »

Top work denis.....so engine swap 2 is nearing completion

batsbats · « **Reply #91 on:** September 05, 2008, 12:42:39 PM »

Nicely done.

dude8383 · « **Reply #92 on:** September 05, 2008, 05:16:31 PM »

Quote from: e30guydownunder;56085

Top work denis.....so engine swap 2 is nearing completion

indeed it is

i hope to wire it up this weekend and start it up!

Quote from: batsbats;56099

Nicely done.

thank you

i'm quite proud of myself to have gone this far.

She loved E · « **Reply #93 on:** September 05, 2008, 07:15:54 PM »

Nice work!!!!

Q: How many swaps/engine builds have you done before? You make it seem easy, but I have a feeling there's a lot more to it than just taking everything apart and putting it back together. :cool:

dude8383 · « **Reply #94 on:** September 16, 2008, 10:49:29 AM »

Quote from: She loved E;56120

Nice work!!!!

Q: How many swaps/engine builds have you done before? You make it seem easy, but I have a feeling there's a lot more to it than just taking everything apart and putting it back together. :cool:

haha well this would be my third swap but my first 24V swap.

dude8383 · « **Reply #95 on:** September 16, 2008, 10:58:23 AM »

Some more progress for you guys.

Jimmy Lewis · « **Reply #96 on:** September 16, 2008, 12:59:30 PM »

Raw. Looks great, progess is wonderful.

dude8383 · « **Reply #97 on:** October 02, 2008, 06:15:18 PM »

EDIT: Including the specs on car

M50 Block
M52 Crank
M52 Rods
M52 Pistons
S50 Cams
M52 Exhaust Manifolds
Intake and Exhaust ported (every bit helps)

okay, so this thing won't bloody start...

i have fuel, i have current going to coil and definitely have vacuum.

i checked robertk's thread about the auto tranny switch (pin 65 on ecu) and provided a 12v current and still nothing.

i will attempt to pull the coil pack and actually plug the spark plug into it and then crank to see if spark plug is actually getting current.

it also has the EWS delete chip.

i am almost convinced it is the crank position sensor but haven't tested it yet.

here are two vid's of how it cranks:

http://www.youtube.com/v/-7dhzX4VI-4&hl=en&fs=1

http://www.youtube.com/v/19BHqB8IaCg&hl=en&fs=1

anyone have any ideas?

kowalski · « **Reply #98 on:** October 02, 2008, 08:07:02 PM »

i would have suggest both of the things you have planned.

dude8383 · « **Reply #99 on:** October 04, 2008, 07:40:54 PM »

Started it today!!!!!

That dash of oil helped fire this thing up like nobody's business.

I'll have the video up shortly! It sounds pretty good to me, but I can barely tell cause this thing is so flippin loud.

It won't idle though so I need to look into why...me thinks it is the M44 318i MAF

Link to youtube:

http://www.youtube.com/v/YuhyX0rpE5o&hl=en&fs=1

On a side note we should add the youtube ***** feature...its freakin awesome.

Jimmy Lewis · « **Reply #100 on:** October 04, 2008, 08:08:56 PM »

That thing is going to roar. And your ACT Weaves look badass on the shwarz. I think I'm going to go the M52 route when my engine gives out, but not as built as your motor. Good stuff, I can't wait to see it all together and some in car vids.

dude8383 · « **Reply #101 on:** October 05, 2008, 11:50:07 AM »

Quote from: Jimmy Lewis;57890

That thing is going to roar. And your ACT Weaves look badass on the shwarz. I think I'm going to go the M52 route when my engine gives out, but not as built as your motor. Good stuff, I can't wait to see it all together and some in car vids.

thanks man!

next weekend i should get the exhaust work done so that i can start driving it!

tim_s · « **Reply #102 on:** October 06, 2008, 02:01:39 AM »

me thinks you're right - get the m44 MAF off it! glad it's firing.

dude8383 · « **Reply #103 on:** October 06, 2008, 11:21:56 AM »

Quote from: tim_s;57950

me thinks you're right - get the m44 MAF off it! glad it's firing.

haha thanks man.

i picked up a maf on ebay. i hope it comes in before the weekend

PaulC · « **Reply #104 on:** October 06, 2008, 11:36:02 AM »

Nice work, man. Congrats.