Author Topic: Shift_Now  (Read 4214 times)

Shift_Now

  • Newbie
  • *
  • Thank You
  • -Receive: 0
  • Posts: 37
    • View Profile
Shift_Now
« on: May 20, 2007, 11:15:16 AM »
Well I've been a memeber of this site for some time, and I've never poseted a picute of my car, so here it goes: I bought it as a "total loss" vehicle (it had the rear quarter panel and rear panel smashed in) mostly for the wheels, but then I felt obligated to see it back on the road.  It curently has over 306,000 kms on it, short shifter, chip, 4.45 differential,  21mm front sway-bar, 14.5 rear sway bar, M-Tech II front and rear bumpers, M-Tech II spoiler, 16" BBs rims, ///M3 springs (soon to be replaced by proper lowering springs), full alpine stereo, black Recaro seats out of an e21 320i, and a custom 2.25 exhaust(cat delete, resonator, Dynamax muffler).  Enjoy.

rhogg

  • Jr. Member
  • **
  • Thank You
  • -Receive: 0
  • Posts: 86
    • View Profile
Shift_Now
« Reply #1 on: May 20, 2007, 11:37:26 AM »
Nice Job - very clean.  

As a Canadian I'm curious as to where you are sourcing parts.  We are  3 months into our rolling restoration and while parts are available I am getting either killed at the dealer, or killed with shipping from the US.  Any Canadian pointers?

Shift_Now

  • Newbie
  • *
  • Thank You
  • -Receive: 0
  • Posts: 37
    • View Profile
Shift_Now
« Reply #2 on: May 20, 2007, 11:49:13 AM »
I've gotten most of my parts from parts cars.  The body kit+spoiler I got when I bought a "total loss" e30 M-Tech 320i (2.0L inline 6) some kid imported from Japan.  As for the actual body panels, I had to take the hit and buy from the dealership (only about $1000 for quarter panel and rear panel).  And most of the little parts I've either bought from small independent BMW repair shops, eBay, or used one of my dad's 3 parts cars (he currently ahs 2 complete cars parted out into about 20 large Rubbermaid containers).  my dad and I are into the e30 restoration as well, we have already restored a '87 325i convertable, and we are in the process of fixing a e30 320it (TOURING!)

Alpine003

  • Hero Member
  • *****
  • Thank You
  • -Receive: 0
  • Posts: 848
    • View Profile
Shift_Now
« Reply #3 on: May 20, 2007, 12:05:23 PM »
Very nice. Now you just need some sideskirts to complete it.

silverblades181

  • Sr. Member
  • ****
  • Thank You
  • -Receive: 0
  • Posts: 396
    • View Profile
Shift_Now
« Reply #4 on: May 20, 2007, 08:37:56 PM »
How do you like the 4.45 in everyday driving? Did you run the 4.10 before to compare? Is it LSD? Nice car. Restoring E30s is very noble! Good job.

E30 318is 1991 (Diamantschwartz) - Parts car
E30 318is 1991 (Brilliantrot)
Bayerisch Motoren Werke

Shift_Now

  • Newbie
  • *
  • Thank You
  • -Receive: 0
  • Posts: 37
    • View Profile
Shift_Now
« Reply #5 on: May 21, 2007, 04:03:20 PM »
in everyday city driving, the 4.45 is really nice, it makes it really easy to launch the car and it makes it so you don't always have to downshift to go places, and on the highway, it keeps the revs at 2800 at a steady 100km/h, and higher than that and the revs tend towards 3500.  No, unfortunatley it is an open diff.  And yes, I have M-tech II sideskirts, but I don't knwo if I want to drill all the extra holes in the body to put them on, so I'm looking for a different alternative.

gearheadE30

  • Legendary
  • ******
  • Thank You
  • -Receive: 0
  • Posts: 1245
    • View Profile
Shift_Now
« Reply #6 on: May 21, 2007, 04:28:09 PM »
Looks like a nice car, and an Alpine, too!!

What car is the 4.45 out of? I was under the impression that the numerically highest stock ratio was the 4.27 out of the 318i convertible.

1991 318is Turbo
1989 Caprice Classic Wagon named Humphrey
1979 Suzuki GS750E

Alpine003

  • Hero Member
  • *****
  • Thank You
  • -Receive: 0
  • Posts: 848
    • View Profile
Shift_Now
« Reply #7 on: May 21, 2007, 10:41:15 PM »
Quote from: Shift_Now;26240
And yes, I have M-tech II sideskirts, but I don't knwo if I want to drill all the extra holes in the body to put them on, so I'm looking for a different alternative.


I've never seen the insides of the Mtech2 sideskirts but you might want to look into 3M body panel adhesive. This is the stuff a lot of the OEM manufacturers are starting to use. Once attached, it will not come off.

Shift_Now

  • Newbie
  • *
  • Thank You
  • -Receive: 0
  • Posts: 37
    • View Profile
Shift_Now
« Reply #8 on: May 24, 2007, 01:50:37 PM »
The 4.45 came out of the 320i M-tech I bought out for SGI Salvage.  that car had an automatic transmission, so my guess the 4.45 was to compensate for the loss in acceleration caused by the automatic.  And I read somewhere that some European Evo III M3's came with a 5.20(or something around there).

gearheadE30

  • Legendary
  • ******
  • Thank You
  • -Receive: 0
  • Posts: 1245
    • View Profile
Shift_Now
« Reply #9 on: May 24, 2007, 07:10:59 PM »
Thanks for the info, although with a 5.20 wouldn't the M3 only be able to get up to about 120? Sure, acceleration would be killer, but it would kind of suck on the highway...

I also learned that the E36 318it had a 4.45, although LSD is almost impossible to find.

1991 318is Turbo
1989 Caprice Classic Wagon named Humphrey
1979 Suzuki GS750E

Shift_Now

  • Newbie
  • *
  • Thank You
  • -Receive: 0
  • Posts: 37
    • View Profile
Shift_Now
« Reply #10 on: May 24, 2007, 10:08:37 PM »
yea, but I tihnk those Sort Evo M3's were built so BMW could put them in a certain race class or something like that, so they were pretty much race cars, with thinned windows, and lighter pannels, so 120 would probably be about right.  To be honest I don't even know if 4.45 came in a LSD.  Maybe it did, but I recently bought the "e30 BMW Restoration Bible" and it didn't even list a 4.45 as an optional differential.  But here one is.  But yea, I wouldn't go back to a 4.10, becasue the 4.45 makes me think twice about speeding on the highway, and being only 16 years old, thats a good thing!