Messages

1

For Sale / M42 head -- in Olympia WA

« on: October 15, 2011, 01:32:26 AM »

I've got a head for an M42. has a couple bent valves. I don't know which ones however. The head has been surfaced, pressure tested, repaired -- the whole works. When I got it all put back together, the tensioner failed and the chain jumped-- presto -- some bent valves.
I'll let it go pretty cheap. It's got the cams still. No sprockets. $100 OBO picked up locally-- I could ship it if necessary, but it would be a little spendy.

2

For Sale / M42 head

« on: July 28, 2011, 05:48:39 PM »

As of today, 7/28, I still have the head. Shipping to 89121 by FedEx ground is approximately $45, and approx 4-5 days.
That would include the cams, etc.

3

WTB/WTT / wtb: water pump pulley

« on: July 23, 2011, 12:38:45 AM »

still need one? I might have one in the garage. let me know

4

WTB/WTT / WTB 93' E36 Water Pump Pulley (V-Belt)

« on: July 23, 2011, 12:36:07 AM »

still need one? i think i have one, but i'll have to check in the garage.

5

WTB/WTT / WTB M44 lower timing case, M42/44 timing cover

« on: July 23, 2011, 12:34:19 AM »

if you still need them you can pm me or email at olyleroy@hotmail.com  I have them

6

WTB/WTT / Wanted 91 e30 m42 fuel pump.

« on: July 23, 2011, 12:28:54 AM »

I have used a TREperformance fuel pump with good success on both my 318i and 325es. Here's the link:  http://www.treperformance.com/FuelPumps/TRE255FuelPumps.html

7

WTB/WTT / Wanted E36 318i Cylinder Head

« on: July 23, 2011, 12:23:54 AM »

I'm not sure if it matches, but I have a head from a 91 318i, it's an M42. I'm in Olympia WA. so, either pm me, or email at olyleroy@hotmail.com. i'll give you details

8

For Sale / head and block

« on: July 18, 2011, 07:50:33 PM »

I can check if you are interested

9

For Sale / head and block

« on: July 18, 2011, 05:34:34 PM »

I've got a head with bent valves (the tensioner failed on 1st startup after getting it back from the machine shop). it's been pressure tested, shaved (it's at minimum spec). All is good. I'll include the sprockets, cams, etc. i will ship if you want it and are not local. I'm in Olympia WA. How about $125 obo?

10

For Sale / M42 block, head

« on: May 30, 2011, 05:52:45 PM »

I have an M42 out of a 91 318i that I need to get rid of soon. I just had the head machined (it is at minimum spec), but the tensioner was stuck so the chain jumped on start up and the valves are most likely bent. Therefore... off she goes. I will take the best offer, and will include the valve cover, the oil filter reservoir, the exhaust manifold. does not come with oil pan however, sorry. but anything else that I have that you may want i will either throw in or make a good deal for. I also have a few parts from a 325e. Thanks.  PM me or my email is olyleroy@hotmail.com.

11

For Sale / 91 318i parts

« on: October 04, 2010, 01:53:50 PM »

Hi everyone, I am relatively new to the forum, although I have had a few E30’s, (currently 2) and a couple other models for a few years, and love them. And you all have a great forum.
I need to sell some parts from my 91 318i, and some from an 84 325e. the motor parts listed and shown here are from the 318i M42. The other parts are from the 325. I am open to offers.

Block: as is $225
Head: has been repaired, shaved, is at minimum spec, valves bent when the chain jumped. $100 without cams, crank etc.
valve cover: $75
crank: $50
cams: $50 each
sprockets: $20
Chain: $20
anything else, let me know. anything can go.
Intake: $50 for either or $75 for both
motor mounts: $15
thermostat housing: $15
fan clutch: $15 SOLD
throttlebody hose and heater plate stuff: $5
ICV: $10 SOLD
taillights: $30 for the right, $25 for the left, and $45 for both
side markers: $10 for both
e brake boot: $5
dash:  $150 -this dash is near perfect. it has a small wrinkle above the glove box opening. but i won’t put heat to it, whoever buys it can. I will also throw in all the a/c-htr duct work, the additional trim pieces (around the inst cluster, the steering column, by the glove box,etc.)
door panels (for a 2 door): $50 and I will include all trim and arm rests. the panels need a little gluing on the back side.

Of course these prices do not include shipping. I’ll ship it any way you prefer. I’m in  Olympia, WA 98503. Link to pictures:

http://picasaweb.google.com/108183728830648989126

If you would like to email me directly: olyleroy@hotmail.com
Thanks for your interest!!


 










































































































12

For Sale / 318i part out

« on: August 06, 2010, 10:23:39 PM »

how much for the air flow meter if you still have it? i'm in washington state