1
For Sale / Re: FS: M42 Motor PARTS and driveline CT
« on: April 08, 2014, 04:44:36 PM »
Hi there, if the engine is from e30 and if you are willing to dismantle that much, I need the intake cam.
Thanks
Thanks
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
General Topics / Re: MAF Conversion: It's Happening, Who Is Interested?
« on: December 09, 2013, 05:41:50 PM »
Hi bmwman,
I've been away from our forum for a long time and I was assuming that you have finished your kit and has sold many of them already. And finally I logged on to buy one for myself with a tought of finding a burning threat at the very top of the other threats. But, I have found a deserted one
So I did read the last messages and I can see you are busy with the new responsibilities. I wonder, are you planning to go back to maf kit project any time soon?
I've been away from our forum for a long time and I was assuming that you have finished your kit and has sold many of them already. And finally I logged on to buy one for myself with a tought of finding a burning threat at the very top of the other threats. But, I have found a deserted one
So I did read the last messages and I can see you are busy with the new responsibilities. I wonder, are you planning to go back to maf kit project any time soon?
3
Member Profiles / sfinsf
« on: November 18, 2012, 10:16:08 AM »
Good work mate, I wish I had some space to work on the car...
4
General Topics / MAF Conversion: It's Happening, Who Is Interested?
« on: November 05, 2012, 02:50:42 PM »
Yeah any news on this? I haven't been here for ages and just seen this thread. I would definitaly buy one.. In fact I'm the one who e-mailed you in 2006 to buy your kit but, at that time you weren't willing to sell because of this low rpm wot hesitation issue.
5
Engine + Driveline / 2-3K rpm Vibration
« on: November 03, 2012, 12:29:23 PM »
I have exactly the same problem eversince I bought the car since from 2003. I have came a long way, changed the engine mounts with originals, AFM, plugwires and later on COP conversion, 4 pintle injectors, and lately an adjustable fuel regulator. Everything has helped and made the engine smoother but this 2800 rpm vibration still exist. I removed the driveshaft vibration damper and that didn't make any difference. This front silencer theory is interesting though. I still have the original (might be clogged) and causing the problem?
6
For Sale / parting out m42 engine
« on: October 31, 2012, 07:54:24 AM »
I will contact you through PM tomorrow for the shipping address. It's not going to be Australia, going to be US. Thanks
7
For Sale / parting out m42 engine
« on: October 29, 2012, 03:03:51 PM »
Sorry for the late reply. The AFM has never been opened, right? If so I am buying both the AFM and the upper intake manifold. Am I paying with paypal?
8
For Sale / Parting m42. Wy
« on: October 27, 2012, 06:28:20 PM »
I'm interested in the AFM and the upper intake manifold..
9
For Sale / parting out m42 engine
« on: October 27, 2012, 06:22:07 PM »
Do you have the AFM? I am interested in the AFM and the intake manifold.
10
For Sale / FS: M42 engine parts in Charleston
« on: October 27, 2012, 06:18:18 PM »
I need an unopened AFM. Do you have it?
12
General Topics / AFM voltage help for MAP conversion
« on: May 21, 2009, 03:42:21 PM »Quote from: Jimmy Lewis;72091
Do you mean volts or ohms? I'm assuming they want the ohms of the potentiometer at those different times. Maybe I'm wrong, but if you can get back to me and tell me what you mean I'll go out and take down some numbers for you.
Thank you Jimmy, I'll talk to them tomorrow to find out this volt and ohm issue. And I will post what they say...
Quote from: colin86325;72092
It's a 5V power supply. The spec is for .2 to .3V at idle.
This is from the repair manual--hopefully somebody can verify. I don't have a DVM to test it myself.
Oh yes, it works with 5V. Do you mean 0.2V when the ignition on and engine is not running and 0.3V when the engine is on idle?
Again thank you very much
13
Engine management / AFM voltage help for MAP conversion
« on: May 21, 2009, 03:31:56 PM »
I thank you guys, I will talk to the company about this wear issue and will post again tomorrow what they really want to know...
14
Engine management / AFM voltage help for MAP conversion
« on: May 19, 2009, 11:13:10 AM »
Nobody?
15
General Topics / AFM voltage help for MAP conversion
« on: May 19, 2009, 11:12:21 AM »
Guys, please I'm still waiting. If any of you have a voltmeter, it's just a minute thing to find out this numbers...