M42club.com - Home of the BMW E30/E36 318i/iS

PAPER OR PLASTIC => For Sale => Topic started by: Niterider11 on January 10, 2011, 09:55:53 PM

Title: Parting out complete M42 engine from a 91 - CA
Post by: Niterider11 on January 10, 2011, 09:55:53 PM

Hey everyone I have for sale every part from a 91 M42 minus starter, flywheel and cylinder head.  Cylinder head was cracked so I ended up swapping in a new engine.  Had 154k on it when I took it out.  I will post pics tomorrow, if interested in any parts let me know.  Also willing to trade for interior parts such as seats door panels carpet and center console

Title: Parting out complete M42 engine from a 91 - CA
Post by: DesktopDave on January 10, 2011, 10:12:59 PM

I wish you were closer.  Shipping big bits like door cards cross-country will be expensive.  I'd be interested in the timing case, especially if the cam gears are good.

I have some late model sedan tan fabric panels that are in OK shape.  I know I have a few center consoles from sedans too.

Title: Parting out complete M42 engine from a 91 - CA
Post by: Niterider11 on January 10, 2011, 10:16:29 PM

I havent even looked at gears but I will tomorrow and post pics for you.  Sorry looking for black or grey interior

Title: Parting out complete M42 engine from a 91 - CA
Post by: Gerta318is on January 14, 2011, 03:05:32 PM

I have a set of door panels and sun visors (passengers and drivers side).  Id be interested to know if you have the complete battery hold down set up.

Title: Parting out complete M42 engine from a 91 - CA
Post by: timc1018 on April 17, 2011, 08:56:22 PM

looking for a dual mass flywheel for my son's 91 318is (M42)...

Title: Parting out complete M42 engine from a 91 - CA
Post by: DesktopDave on April 17, 2011, 09:10:14 PM

Timc1018 - Hate to say it but you might have some better luck over at r3v...if you haven't done it already, that is.  Sadly, a lot of M42's get swapped out over there, you're sure to get one or two reasonable offers.

Have you considered the single-mass conversion?  You might want to PM JoeDelio from this thread (M50 flywheel setup) (http://www.m42club.com/forums/showthread.php?t=13375).  Great price IMHO.

Title: Parting out complete M42 engine from a 91 - CA
Post by: 91318isfoundation on April 23, 2011, 06:48:53 PM

hey how much would u want for the lower and upper oil pans along with the pickup tube and all the other macaroni in the oil pans

Title: Parting out complete M42 engine from a 91 - CA
Post by: BimmerJon on April 26, 2011, 11:47:51 PM

Interested in the crank pulley if you have it!  Thanks!

Title: Parting out complete M42 engine from a 91 - CA
Post by: e30work on May 06, 2011, 10:20:55 PM

you got PM

Title: Parting out complete M42 engine from a 91 - CA
Post by: sailer6460 on August 28, 2011, 10:21:09 AM

PM sent

Title: Parting out complete M42 engine from a 91 - CA
Post by: M5wanaB on August 28, 2011, 12:42:19 PM

looking for an exhaust cam and tray as long as it does not have any scoring on the journals.

Title: Parting out complete M42 engine from a 91 - CA
Post by: Brink on August 28, 2011, 01:47:36 PM

Interested in the whole bottom end, pm'd you